My middle son is jumpy and crazy and skinny and tall–all of which make his pants fall down quite often (if he is wearing pants that is), so I thought I’d make a belt for him. In honor of Celebrate the Boy month at Made and Made by Rae I  drew up a pattern to share with all of you.

The finished belt is 1 1/2 inches wide and adjusts to fit waist sizes of about 20 inches to 24 inches. To make a different size take the waist measurement you want to use then add 8 inches: the main fabric will be (waist size + 8)inches by 3 1/2 inches and the lining fabric will be one inch shorter.

Materials:

• one piece of fabric cut 30 inches long and 4 inches wide, preferablly cut parallel to the selvege, but as long as it’s not cut on the bias it will work out just fine.
• one strip of canvas or denim (or something that is a similar weight) 29 inches long and just shy of 1 1/2 inches wide.
• three snaps and snap setting tool
• one 1 1/4 inch D-ring
• scissors, pins, iron, sewing machine

Steps:

1. Fold your strip of fabric in half the long way (wrong sides together) and press.
2. Open the fabric back up and with the right side down, fold the top edge down 1/2 inch and iron, then fold the bottom edge up 1/2 inch and iron.
3. Set your strip of canvas or denim on the bottom half and fold both short ends over it and press
4. Miter your corners: fold the corner diagonally, so it makes a right triangle where the middle of the longest side (the hypotenuse if you paid attention in geometry) of the triangle lies on the point where the folds of the short end and the long side meet. This makes much more sense if you just look at the picture. And this is just how I do mitered corners, of course you can do it any way you know how.
   
5. Sew all around the belt anywhere from 1/8 inch to a 1/4 inch from the edge–whatever looks best to you.
6. Pick one side of the belt to be the right side (the one that will face out) and put that side down. Slide the D-ring onto the left end of the belt, fold the end over it one inch and sew down. Sew back and forth a few times to make sure it’s secure.
   
7. Now for the snaps (I used heavy duty snaps for the wood grain belt, but there are a lot of options out there). With the right side down again and the D-ring to the left, attach the top part of three snaps: the decorative part on top and the male part (for lack of a better term) of the snap on the right side of the belt. The snaps should start about 1/2 from the end and be about an inch or so apart.
   
8. 6 inches to the left of the last snap attach the bottom part of the snap: the female part of the snap should go on the right side of the belt and the very bottom piece of the snap should go on the wrong side  (the side that will face in). This seems wrong, but it’s not. The belt will go through the D-ring and then fold back on itself and snap.
   
9. Find some pants with belt loops and try that sucker out!  Look at you, you just made a belt!

Variations:

• To make a skinnier belt, your fabric strip should measure 30 x 2 1/2 inches and the lining should be 29 x 3/4 of an inch. Then just follow the directions for the wider belt.
• I thought it would be nice to have a fabric buckle for baby belts (yes, it’s ridiculous I know, but so are baby sneakers and I bet you have some of those) so the metal doesn’t jab their pudgy tummies, or if you don’t have a d-ring around, or if you’d just like to make a cool fabric buckle, whatever, this is how you do it:
  Cut a piece of fabric that is 6 x 2 inches (for the skinnier belt, cut 4 x 2). With right sides facing sew the ends together, so you have a small fabric ring, then fold both the edges in (wrong sides together) to meet each other in the middle. Fold in half again and sew. It’s easiest to sew with the loop going up over your presser foot than the other way around. Attach the fabric buckle just like you would the D-ring, making sure the seam is hidden under the fold and the nice side is facing out.
  
• Buttons! Sew button holes where the snaps would go and then sew some buttons on.

There are so many other things that can be done with this belt: topstitching, grommets, snaps all around, a matching mama belt! If you make one from this tutorial (or any other tutorial of mine) remember to add it to the elsie marley flickr group.  And please add a photo or two to the Celebrate the Boy group on flickr too!

Go Boys!

Erin is responsible for most of my daughter’s summer wardrobe, this year and last.  Her tutorials are easy to follow and super adaptable. I made a bigger size of the Twirly skirt this year, but it seams my daughter didn’t grow that much so I guess it will fit next year too.  Though I’m sure I’ll want to make another one when next summer comes around. I’ve got some more summer clothes for her in the works, but not much planned for my son. Are there any good, stylish tutorials or patterns for boys out there, beside the ubiquitous “easy pants?”

On a completely unrelated note, I’ve been asked to make the pattern for my kiddy messenger bags available for purchase. I would love to do this, but worry about copyright and pattern bootlegging (ha!). Do any of you sell PDF patterns? And if so do you have any advice on the subject?

I made a rhubarb custard pie yesterday after picking up some lovely rhubarb at the farmer’s market. My mother made this pie every spring and would always say that it proved the existence of god. And really it is damn good. The recipe is from Betty Crocker and it’s quite simple, but the lattice top makes it look extra impressive.  I took some pictures while I was putting the pie together and though I’d share a little lattice top tutorial so all your pies can look fancy fancy too.

Make enough pie crust for a 2 crust pie (there is a good recipe here). Roll half out and line your pie pan, put you filling in and pop it in the fridge while you roll out the other half of the dough. Roll the second half out just like the first: about an 1/8″ thick and slightly bigger than your pie pan. Cut the whole thing into one inch strips. Now place two of the longest strips in the middle perpendicular to each other. Fold the strip that is underneath back over the strip on top and add another parallel to the one on top about a half an inch away. Continue weaving the strips by folding every other strip up and putting a new strip in. If your strips are broken or you don’t have enough long ones, just hide the broken bit under another strip and no one will ever know. When you’ve covered the whole top, seal the pie by pinching the top and bottom crusts together (two fingers on the outside and one on the inside, just like the picture) around the whole pie. With a sharp knife cut all the excess dough off and stand back and admire your work. Before putting in the oven be sure to brush the top with cream (or egg wash) and sprinkle with sugar. This will make the lattice top look even better.

Rhubarb Custard Pie
from Betty Crocker

3 eggs
3 Tbsp. milk
2 cups sugar
1/4 cup flour
3/4 tsp nutmeg
4 cups cut-up rhubarb
1 Tbsp butter

Beat the eggs and milk in a large bowl. Mix the sugar, flour and nutmeg together and add to the eggs. Mix well. Add the rhubarb and stir. Pour into your prepared crust. Dot with the butter. Cover with lattice top. Bake for 50-60 minutes at 400 degrees (Fahrenheit) until nicely browned. Serve slightly warm (with vanilla ice cream!) or cold for breakfast the next day.

Here it is, the string of lights advent calendar tutorial (and pattern!). I made the pdf pattern file all by myself for the first time, so if you have problems with it just email me and I’ll try to fix it. Otherwise, hurry up! because advent is almost over!

materials

green wool felt
multi-color felt scraps
60 feet green yarn
green embroidery thread
lightweight treats (gum balls, dum dums, love notes, tiny ornaments)

pattern

download here

directions

Cut the yarn into six equal pieces (10 feet each or 120 inches each or about 3 meters each). Take three pieces and braid them together. This is more difficult then it sounds, but if you roll up the slack and just work with a little yarn at a time it’s much easier. Braid the other three together the same way. Then twist the two braids together and knot the ends.  It will stay twisted when you sew the lights to it.

Cut out 25 (or 24 or however many lights you want) circles and rectangles. Create the socket by sewing a blanket stitch to the edge of rectangle and the circle attaching them to each other.  If the rectangle is slightly longer than the circumference of the circle clip it to fit and continue sewing the ends of the rectangle together. Sew the sockets onto the cord–one every three inches.

Cut out the light bulb pattern piece. To sew the lights up faster you can fold your colored felt over and simply trace the pattern onto it with a marker (permanent or not it doesn’t matter) then sew the two pieces together staying inside the lines.  To be safe test the first light to see if it fits: sew and turn out, put a treat or two inside, then fit it inside the socket and see if it stays when it’s hanging upside down. If it slips out, just make the lights slightly bigger.  If you’d rather use the lights for decoration and not for treats you can stuff the light bulbs lightly and sew them onto the socket.

I didn’t really finish the ends of the cord (I just tied a knot on both ends).  But it would be sweet to make a little plug out of felt to hide the knot. To do this cut out four extra “socket bottom” circles and two extra rectangles.  Cut a slit in the middle of one of the circles and insert your knot, then attach the rectangle, just like you did for all the sockets, and attach the other circle to the other side–making a  round (European style) plug. You can even make some prongs out of felt to complete the look.

download the pattern here.

I made this half eaten gingerbread man last year, but I thought I’d post it again in case you are starting to freak out about how soon Christmas is (16 days). He’s super simple to sew up. I wrote up instructions and there is a pattern you can download too. If you’d like to see the other mutant gingerbread man I made click here and to know why I made them click here.

Plenty of you want a tutorial for the string of lights advent calendar, so look for that in a couple days. Now get off the computer and finish those christmas presents already.